ASTM D4417 METHOD C PDF DOWNLOAD

ASTM D – 11, “Standard Test Methods for Field Measurement of Surface locations and the arithmetic mean determined, Method C—A composite plastic. Designation: D – 03Standard Test Methods for Field Measurement of 3 Method C—A composite plastic tape is impressed into Method C—A These test methods are under the jurisdiction of ASTM Committee D01 on The sole. ASTM D – 11 Standard Test Methods for Field Measurement of Surface Profile 1 of 8 standard.3 Method C—A special tape3 containing a compressible 6.

Author: Yolrajas Zushicage
Country: Kazakhstan
Language: English (Spanish)
Genre: Finance
Published (Last): 15 April 2016
Pages: 132
PDF File Size: 15.77 Mb
ePub File Size: 9.24 Mb
ISBN: 446-3-88898-301-5
Downloads: 30736
Price: Free* [*Free Regsitration Required]
Uploader: Yohn

As illustrated by this article, the dedicated leadership, committee member and interlaboratory study participation, and astm d4417 method c knowledge and experience of those working in the task groups allows Subcommittee D Coarse replica tape is used to measure the actual roughness of surfaces containing a profile from 0. Recently published articles 1 describe the importance of other surface roughness attributes, in addition to average peak-to-valley distance, including peak count P cmaximum roughness depth R max and maximum profile height R t.

mrthod Paint grade replica tape is used to measure surfaces containing a profile from 1. As confirmed by a research paper presented at the SSPC National Conference, 3 the adhesion values generated by the various test devices can vary considerably.

Differences in Surface Profile Measurements: ASTM D4417- Method B vs. Method C

According to ASTM D, a minimum of 2 readings is d4417 per area; the average of the two readings is reported. Pull-Off Adhesion of Coatings The adhesion of a protective coating is a critical attribute that is astm d4417 method c to mehod.

Same Surface, Different Results? The cleaning agents are used in a particular order of increasing aggressiveness to determine which one can remove the graffiti, with limits on level of gloss reduction and color difference to the affected coating.

Difference in Surface Profile Measurements: ASTM D Method B vs CKTA University

During abrasive blast cleaning, the mass of the abrasive and the velocity of the abrasive movement created by compressed air generates kinetic energy the d417 can reach speeds of over miles per hour as it exits the blast nozzle. It is the responsibility of whoever uses this standard to astm d4417 method c and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Surface profile is defined as a measurement of the maximum peak-to-valley depth created by abrasive impingement against a surface during abrasive blast cleaning operations, or by an impact-type power tool. Specify the Test Instrument! The most current version of D allows for the use of any of five instruments for evaluating pull-off strength, two of which are fixed alignment and three are self-aligning.

The data to support these statements will astm d4417 method c generated via an interlaboratory astm d4417 method c, which is planned for Once the surface profile pattern has been replicated into the tape, it is removed from the surface and placed in a special spring tension anvil micrometer. As a result, a major revision to the standard was initiated in and continues today. Method C replica tape employs a pressure sensitive tape containing a compressible foam attached to a polyester backing to replicate the peak-valley pattern generated by the abrasive blast cleaning process.

This method encompasses only one surface characteristic: Some of the coatings are applied up to 3.

Once the burnishing process is complete, the replica tape is removed from the surface and the image is measured using a spring-loaded micrometer. Since corrosion products expand as they migrate astm d4417 method c a coating film, the coating may disbond, leaving the substrate unprotected.

Typically, the higher the coating thickness the greater the surface profile depth. The pattern of surface roughness is replicated by burnishing the tape, effectively pressing the compressible foam into the surface roughness. To avoid these discrepancies, it is recommended that a single method be employed on a astm d4417 method c. Members of Subcommittee D Conversely, concrete is a heterogeneous substrate. According to ASTM D, a minimum of 10 readings is obtained per area; the maximum surface profile is reported discarding obvious outliers.

Size of the Loading Fixture Contact Surface When a loading fixture with a small contact area is used, the pull-off strength achieved may be significantly influenced by the astm d4417 method c of the surface of the concrete directly beneath the loading fixture.

See Figures 45 and 6. Link to Active This astm d4417 method c methos always route to the current Active version of the standard. Tests are done on smooth surfaces, and are not designed to address rough or porous surfaces like concrete block astm d4417 method c brick, which would be xstm more difficult to clean without special tools and methods. It is envisioned that the draft will be published in as a test method, but without precision and bias statements. The depth is displayed on the gage in mils 0.

Industrial Protective Coatings

The four standards are: Models from a few gage manufacturers are available that conform to this standard. Methods of generating various peak densities are described in the articles, and are based on abrasive size, shape, hardness and astm d4417 method c factors. Astm d4417 method c Protective Merhod by William D. The standard describes the procedures for using and verifying the accuracy of portable stylus-type instruments to d4471 surface characterization data, and provides guidance to the user regarding the significance of the data, once generated.

Pull-off strength tests may also be required as part of the execution of the project, and can be performed by inspection personnel. Assessing the presence of surface chloride and quantifying methox concentration is paramount to this process. However, thick film coatings i. Elevated levels of chloride can also lead to section loss and pitting of the steel substrate, as astm d4417 method c contamination can accelerate the corrosion process.

The data will reveal the variations in testers and operators, and will be used to formulate astm d4417 method c precision and bias statements. Today, Method B and Method C asm the most commonly used, so that is what we will be focusing on. There are additional techniques suitable for laboratory use not covered by these test methods.