GY520 MANUAL PDF

Futaba GY Pdf User Manuals. View online or download Futaba GY Instruction Manual. Nstruction, Anual • Read online or download PDF • Futaba GY User Manual. The chart below works for almost all helicopters but you should consult your helicopter manual if you are not sure. Note that I have seen.

Author: Feshura Faegami
Country: Uzbekistan
Language: English (Spanish)
Genre: Video
Published (Last): 23 March 2016
Pages: 75
PDF File Size: 10.86 Mb
ePub File Size: 14.39 Mb
ISBN: 978-8-12727-671-3
Downloads: 18330
Price: Free* [*Free Regsitration Required]
Uploader: Akinogor

The light on the gyro will turn solid Blue.

FUTABA GY520 Manuals

Now quickly press and release the button on the gyro. There is an error in the instructions which has been corrected on Futaba’s FAQ page. If you did not see a change then a common mistake is you got the rudder and gain wires switched around.

On my miniTitan you can see in the right picture that the tail servo is mounted to the tail boom. I’ve never setup a Futaba tail gyro; any ideas?

The first thing to do is make the link slides as free as possible. For the large and class helis use the two thick pads with the metal plate in between.

Make sure you pay attention to the polarity of the receiver manuxl.

If you need to readjust then quickly press and release the gyro button. For a small heli, class ex. When you mount the gyro, use the supplied foam tape. If the tail does not feel solid and lets go when in a high load then increase the gain. The bottom picture on the left also shows another way to look at it, the control lever is parallel to the tail shaft. Rotate the helicopter so the nose moves to the left and watch the rudder servo. If you the tail wags in flight then decrease the gain.

Next check that the gyro can sense the helicopter is moving. It puts manuxl gyro in a standard rate mode so the servo will center when the rudder stick is centered.

If you do not know why the mix is there you can inhibit it by pressing the ‘clear’ button at the bottom right of the radio. To get the tail to move faster or slower, adjust the rudder channel travel. This is going to vary for different helicopters and different brand servos.

Place the servo arm on the servo spline. Turn on maunal radio then connect power to the receiver.

Futaba GY520 Gyro

Register Now In order to be able to post messages on the HeliFreak forums, you must first register. The light will change to a violet color.

This will save the setting. Snap the link on the servo and check that you do not get binding at full left and full right. With the rudder link disconnected from the servo. Click on the photo on the left to see maual other two connections. If everything was okay then the light on the gyro will momentarily change to violet and the servo will travel to manuall other side.

That is very helpful.

Release the button and you will see the gyro manuao repeat a ‘1 blink’. The tail servo will connect to the side that has one socket. Also make sure that your plugs in the receiver have the correct polarity. Heading Manial Solid Blue: Look at the picture on the right.

Just hold it on top of the ball. I helped him some but he downloaded the GY manual and went through setup that way. Adjust to get the maximum travel without binding.

Standard Rate mode Flip the Gear switch up position 0 and confirm that the light on the gyro is solid red.

Standard Rate mode Move the Manuap switch down position 1. It is great they did this so you do not get mixed up. Do the same for ‘GEAR’. This will set it up for the next step.

Futaba GY Manuals

This gyro comes with two servo leads, one with black connectors and the other with red connectors. In the picture you see the link it bent down, the 90 degree angle is in reference to the unbent manuual of the tail control rod. Password Please enter a password for your user account.